Release Notes: October 2020
Last updated
Last updated
The digital certificates for app.thousandeyes.com and downloads.thousandeyes.com, which were previously issued by the DigiCert certificate authority, will be replaced with certificates from the QuoVadis certificate authority on October 13th, 2020. The replacement certificates will use certificate chains with larger key lengths (4096 bits) than the current certificate chain (2048 bits).
Customers who access these servers with clients (browsers, file transfer utilities, custom programs) that use older cryptographic libraries which cannot support 4096-bit key lengths should update their clients. Customers who use supported browsers or other current clients do not need to take any action.
Due to a change in service provider, customers with tests assigned to the Cloud Agent in Paris, France will observe a corresponding change in path-visualization and source IP.
We do not anticipate downtime or impact on test performance. The Cloud Agent ID used within the ThousandEyes API will remain unchanged.
The following Cloud Agent locations now have IPv6 support:
Paris, France
For a complete list of ThousandEyes Cloud Agent locations, see .
You can now gather network data and path-visualization data about proxy servers.
In the past, if your target was behind a proxy, your ThousandEyes tests would not collect network data. Workarounds existed (adding the target to the proxy's bypass list, or creating separate agent-to-server tests to the proxy), but these were cumbersome to configure. And with the popularity of cloud proxy solutions such as Zscaler, Netskope, and Palo Alto Networks, you may want to understand network health to the cloud proxy.
With the ability to run network tests to the proxy, you can more easily correlate data between the application and network layers. The new ThousandEyes proxy capabilities allow you to see
Proxy loss
Proxy latency
Proxy jitter
A visualization of the network path to the proxy
To explore the new proxy metrics:
Go to Cloud & Enterprise Agents > Test Settings.
Select or create an HTTP, page load, or transaction test.
On the Advanced Settings tab, find the Proxy Settings section.
Select Perform network measurements to the proxy.
Several improvements have been made to how Endpoint VPN data is visualized:
VPN loss and VPN latency metrics have been added to the Scheduled Tests, Browser Sessions, and Local Networks views.
The following filters have been added to Endpoint Agent Settings and Endpoint Agent labels:
VPN Vendor: The VPN vendor.
VPN Gateway IP address: The public IP Address of the VPN gateway/server.
VPN Client Address: The private IP via which clients route packets to the VPN tunnel.
VPN Client Network: The private network that the VPN client belongs to.
From te-browserbot version 1.146 and later, installation of an X11 server (via the te-xvfb package) is no longer mandatory. Existing Enterprise Agents will continue to have te-xvfb installed, unless users take action to remove the package. New Enterprise Agents will have the package installed by default, but this can be avoided using one of the following processes:
For Linux package installations: install_thousandeyes.sh now has a new command-line flag to skip te-xvfb package installation.
For Docker installations: Users may create new images based on the official ThousandEyes image that run apt remove te-xvfb.
For TEVA installations: Users may unlock their appliances and run apt remove te-xvfb.
Due to a change in service provider, customers with tests assigned to the IPv6 Cloud Agent in Dublin, Ireland will observe a corresponding change in path-visualization and source IP. The Cloud Agent ID used within the ThousandEyes API will remain unchanged. The new IPV6 IP is: 2001:4d40:4003::/48.
Endpoint Agent labels can now be updated via the API.
Users can now create Endpoint Agent scheduled tests via the API.
Previously, the Account group list API endpoint would only return the organizationName if the user was associated with multiple organizations. This has been changed, and the organizationName will now always be included.
The Import from JS File button in Transaction Test Settings has been replaced with a Create New dropdown menu. This dropdown retains the option to choose a local file to import, but also provides a selection of predefined template scripts. Clicking on an option will update the editor with the contents of the selected template script.
An issue was found where duplicate alerts were inadvertently being created, causing one of the alerts to fail to clear after resolution of the issue. This has been resolved.
An issue was found where updating proxy configuration would refresh disabled tasks, causing them to continue to run despite being disabled. This has been resolved. .
An issue was found where Cloud and Enterprise Agents reported no data on the Map view, even if data was being reported as expected. This has been resolved.
The Endpoint Agent now integrates with the Pulse Secure VPN, providing end-to-end visibility of network nodes and metrics for traffic that traverses the network. When present, the client will populate the VPN Vendor attribute visible in Endpoint Agent views and filters.
Device discoveries now report devices that failed discovery due to a lack of working credentials. The Edit Device modal has also been updated to show the used credentials on the device, and provide users with easy access to new credential creation:
A hard limit of 700 (for example, 50 tests over 14 days, or 100 tests over 7 days) has been added to improve performance when a report or dashboard widget is created with a large BGP data set (either due to no applied filters or too large of a time span). Users are now asked to either apply a BGP test or monitor filter, or to reduce the time span in order to render the data, if it would otherwise exceed the hard limit.
The Internet Insights alert rules functionality has been updated for when both Catalog Providers and Affected Tests are set to Any. Previously, this configuration would only trigger if a customer test was impacted by an outage. The configuration has now been updated to trigger if a subscribed provider is impacted, in addition to if a customer test is affected by an outage in a subscribed provider.
To alert on outages affecting only customer tests (including in providers the customer is not subscribed to), customers should set Affected Tests to Specific, and select all tests, or the specific set of tests you want the rule to match.
In order to simplify test selection in Cloud and Enterprise Agent views, saved events have been removed from the test selector. Saved events can be accessed from the Sharing > Saved Events page in the main menu.
An issue was found where path trace data was not appearing in Endpoint Agent sharelinks. This has been resolved.
ThousandEyes has updated the reports and dashboards user interface, widget icons, and workflow to substantially improve user experience, and ensure that widget addition and configuration is as streamlined as possible:
Widgets can now be added by clicking the + Add Widget button to open the Add a Widget panel, and then either selecting a widget to configure, or by dragging it to the desired location in the report or dashboard.
The Add a Widget side panel is now movable and minimizable, allowing users to review how the added widget looks before saving.
Changes to a widget can be previewed before saving. Clicking Cancel will revert the widget to its pre-configuration state, while clicking Save will confirm the new configuration.
For more information on working with reports and dashboards, see:
Internet Insights customers can now add widgets to reports and dashboards to leverage Internet Insights network outage metrics. The network outage metrics provided are:
Affected Tests: Test data within your organization that is affected by outages.
Interfaces: Interface data affected by outages.
Locations: Location data affected by outages.
Outages: Overall outage data.
Widgets built on Internet Insights metrics can apply the following filter conditions: Catalog Provider, Outage Scope, and Network; Interface Location and Interface IP Address; Affected Test and Affected Domain; and Server Location, Server Prefix, and Server Network.
To add a widget with Internet Insights metrics:
In Reports or Dashboards, click + Add Widget and select a supported widget.
Select Internet Insights as the datasource.
Select Network Outages as the category.
Select a metric and measure (and filters if desired).
A new pre-built dashboard that captures weekly and monthly outage trends has been added for Internet Insights customers. The dashboard, called Internet Insights Built-In, also provides an up-to-date view of the most impacted tests, locations, and providers.
